Epson Projector Remote Not Working? (Try These Easy Fixes!)

Your Epson projector remote not working, and you’re worried? No worries, just keep reading!

The Epson remote control is a great alternative to using the projector’s built-in panel buttons and saves you some time from having to walk over again and again.

Like any other remote, the Epson may develop a fault as a result of discharged batteries, wireless interference, or even existing projector issues.

So, let’s have a look at the quick solution:

If your Epson projector remote isn’t working, move within the “reception range” and improve the remote’s line of sight. If the issue persists, re-program and discharge the remote, insert new batteries and factory reset the projector.

Let’s have an in-depth review of the remote’s issue!

Why is the Epson Projector Remote Control Not Working?

Here’s what can potentially impact the Epson projector remote’s performance:

What Connectivity Type Does Epson Remote Use?

Like most appliance remote controls, the Epson projector’s remote control uses standard IR (Infrared) communication technology to send signals to the projector.

This means that the remote is susceptible to non-visible interference and must be used within a particular range.

“RF” Vs. “IR” Signal?

Unlike the standard IR signals, a Radio Frequency remote control can either use Bluetooth waves or pair directly via Wi-Fi.

Once assigned to a private or local network, the remote will be able to communicate with the device as long as it remains within Wi-Fi range and is “online.”

Epson Projector Remote Not Working – Working Solutions

Tip: The Epson projector remote uses a pair of triple-A batteries and the battery compartment can be accessed after removing the battery cover on the bottom panel. 

1. Move the Remote to Reception Range

There’s a strong possibility that you’re attempting to communicate with the Epson projector while the remote is outside of reception range. 

You must stand within a particular distance of the projector’s receiver for your Epson to accept the commands requested by the remote control.

What is the Epson Reception Range?

The most important factor for achieving uninterrupted communication using Epson’s IR projector remote is standing within an IR range.

Unlike RF controls, IR remotes’ beam is limited to up to 20–25 feet in length, and it will start to degrade after that margin.

Notice: You will not be able to communicate with the projector while the signal is weak or lousy.

Epson Remote’s “Reception Angle”?

Apart from having to meet the particular distance requirements, the remote must also be used in direct line of sight of the Epson projector.

Even if you’re standing close to the Epson projector, a physical object may be blocking the IR signal sent by the remote, preventing it from reaching.

Notice: Identify the exact location of the Epson projector’s “Transmitting” point!

2. Activate Epson’s “Any Projector” Feature

Well, due to the wide range of available Epson projectors, all remotes come with an in-built “Any Projector” feature that allows the remote to pair with any projector.

Hence, if you were unable to program the remote control during the first set-up, verify the “Any Projector” setting is enabled.

So, to activate the remote “Any Projector” feature, press and hold the ID and 0/All buttons for approximately 5–7 seconds.

After that, complete the remote’s programming procedure again and check if it communicates with the projector now.

Quick Tip: The “Any Projector” feature is activated identically on all Epson projector remotes!

3. Power Cycle the Epson Remote Control

A helpful solution against issues with the remote control is to perform a full discharge of the HW components.

Forcing all electricity to exit the Epson remote’s hardware is only possible by temporarily displacing both battery units within the battery compartment and waiting for a bit.

Here’s how to discharge the Epson projector remote in easy steps:

1. Place the Epson projector remote upside down.
2. Next, locate the battery compartment’s cover.
3. Push the cover’s latch downwards to remove it.
4. Next, eject both triple-A batteries from the bed.
5. Wait for 30 seconds while the remote discharges.
6. Place both batteries back in your remote control.

Important: Insert New Batteries!

If discharging the Epson remote did not solve the communication issue, insert a fresh set of triple-A batteries into the remote and position the cover securely.

Hold the remote’s “Power” button for 15–20 seconds to jump-start the new batteries and attempt to use the projector.

Warning: The batteries of the Epson remote may degrade over a few weeks!

4. Reprogram the Epson Remote Control

Well, there’s a possibility that your Epson remote control has temporarily lost connection to the projector as a result of programming issues.

There’s a quick and easy method to reprogram the Epson remote but ensure the projector is turned on and within wireless range of the remote.

Follow these instructions to reprogram the Epson remote to the projector:

1. Ensure your Epson projector is plugged in and turned on.
2. Point the Epson remote control towards the projector.
3. Next, hold the “Enter” and “Home” buttons on the remote.
4. Release once the remote LED light starts flashing slowly.
5. Wait until the Epson remote control is successfully paired.

Note: The programming of the Epson remote control may take up to 50–60 seconds!

5. Resolve Infrared Remote Interference

Unlike remotes communicating via radio waves, standard IR remotes are susceptible to devices producing the same type of signal.

Hence, as a result of the signal congestion, your remote will be unable to communicate with the projector for as long as there is another signal or reflector.

Here are devices that can potentially interfere with the Epson remote’s signal:

• Nearby Bluetooth devices that are currently paired.
• Wireless routers, modems, or any network devices.
• RF transmitters, radios, baby phones, or HT-walkies.

Unfortunately, even devices that communicate on entirely different frequencies can impact your infrared beam waves if they cross paths.

There shouldn’t be any wireless communicator devices in a 15–20 feet range within the projector or the Epson remote control.

What Are IR “Reflector” Devices?

Apart from conflicting signals, devices with a metallic surface, scanner devices, door lock mechanism surfaces, and even microwaves can interfere with IR.

• It’s important to note that the IR beam wave bounces off nearby surfaces before reaching the “receiver” of the projector. 

Tip: You can eliminate a particular device’s interference by unplugging it from the power!

6. Inspect the Epson Projector Unit

One of the reasons why the Epson remote is seemingly not working is due to an underlying projector problem.

If the projector has failed to turn on, does not broadcast properly, or isn’t responding to the remote control, there could be an underlying operating system or HW issue.

Here are a few resolutions to attempt on the projector to restore its functionality:

• Power cycle the Epson projector by unplugging it from power.
• Use the built-in navigation buttons to fully reset your Epson.
• Verify that the projector is receiving sufficient electrical supply.

How to Test Epson Projector’s Functionality?

Fortunately, you don’t have to use the remote to test the projector as there’s a “Menu” button on the top panel of the projector.

So, press the button once and check whether there is any output. 

Tip: You can also test the Epson projector’s broadcasting by plugging in any compatible device!

7. Reset the Epson Remote to Default

If the Epson projector remote is still failing to communicate, you should perform a factory reset.

Like on any other remote, starting a “factory reset” will erase all existing programming profiles and restore the device to initial system settings.

Here’s how to factory reset the Epson remote control:

1. Take both batteries out from the Epson remote control.
2. Hold the “Menu” button on the remote for 5–7 seconds.
3. Next, reinsert both batteries back into the compartment.
4. After that, hold the “Menu” button again for 15 seconds.
5. Reprogram the remote to the projector and start testing.

Notice: If the remote does not have a “Menu” button, use the “Home” or “ID” buttons!

Quick Recap

To fix when the Epson projector remote not working, check for existing IR interference, reinsert the batteries, and power cycle the projector.

If the remote is still facing issues, insert a fresh set of triple-A batteries and factory reset it. Next learn how to fix the Espon Projector’s overhearing issue.